Elecro Poolsmart Plus Heating Controller
Code: EPSHC1
£379.95
These Elecro Poolsmart Plus are an intelligent pond or pool control system that allows you to control and maintain your pond to the perfect temperature as economically as possible.

The Elecro Poolsmart Touchscreen Heating Controller for swimming pools and koi ponds, comes with flow switch and temperature sensor for accurate monitoring and maintaining water temperature.

The Poolsmart Plus Digital Control is supplied fully equipped with flow switch, temperature sensor probe fitted in custom pipe work T-Piece, for simple integration into any pool technical facility.

The Elecro Poolsmart Plus gives you a complete control solution for:
  • Electric Heaters
  • Heat Exchangers
  • Heat Pumps
  • Circulation Pumps
Elecro Elecro Poolsmart Plus Features:
  • Priority Heating
  • Accurate Temperature Control to 0.5ºC
  • Fully Programmable With Timed Control
  • Smart touchscreen display
  • BMS (Building Management System) Integration Ready
  • Multi-lingual interface
  • Programmable 24-hour time clock (4 time zones)
  • Flow and temperature sensor ports
  • Diagnostic display
  • Volt free heating output.
  • Volt free filtration pump output
  • 3 metre long flow switch
  • 3 metre long temperature sensor
  • T-piece with 50 mm and 1.5 inch reducers
Priority heating is when the Elecro Poolsmart Plus digital controller can determine that the ponds temperature has dropped below the minimum required temperature and then switches the ponds heating product (via the control cable) so that the heating product can heat the pond back to the minimum temperature. Once the minimum temperature has been reached the heater will also switch off.

The Elecro Poolsmart Plus Digital Control has been designed to be the most economical heating controller available, by allowing the use of 2 set points you are able to select a higher set point for when fuel is cheaper (i.e. off peak) and then a lower set point for when fuel is more expensive (i.e. peak rate). It is recommended that the lower set point is programmed to be your minimum temperature, if the pond then drops below this temperature during the day the heater can top up the heat to keep the pond at the minimum temperature.

Click Here For Installation & Operating Manual PDF
These Elecro Poolsmart Plus are an intelligent pond or pool control system that allows you to control and maintain your pond to the perfect temperature as economically as possible.

The Elecro Poolsmart Touchscreen Heating Controller for swimming pools and koi ponds, comes with flow switch and temperature sensor for accurate monitoring and maintaining water temperature.

The Poolsmart Plus Digital Control is supplied fully equipped with flow switch, temperature sensor probe fitted in custom pipe work T-Piece, for simple integration into any pool technical facility.

The Elecro Poolsmart Plus gives you a complete control solution for:
  • Electric Heaters
  • Heat Exchangers
  • Heat Pumps
  • Circulation Pumps
Elecro Elecro Poolsmart Plus Features:
  • Priority Heating
  • Accurate Temperature Control to 0.5ºC
  • Fully Programmable With Timed Control
  • Smart touchscreen display
  • BMS (Building Management System) Integration Ready
  • Multi-lingual interface
  • Programmable 24-hour time clock (4 time zones)
  • Flow and temperature sensor ports
  • Diagnostic display
  • Volt free heating output.
  • Volt free filtration pump output
  • 3 metre long flow switch
  • 3 metre long temperature sensor
  • T-piece with 50 mm and 1.5 inch reducers
Priority heating is when the Elecro Poolsmart Plus digital controller can determine that the ponds temperature has dropped below the minimum required temperature and then switches the ponds heating product (via the control cable) so that the heating product can heat the pond back to the minimum temperature. Once the minimum temperature has been reached the heater will also switch off.

The Elecro Poolsmart Plus Digital Control has been designed to be the most economical heating controller available, by allowing the use of 2 set points you are able to select a higher set point for when fuel is cheaper (i.e. off peak) and then a lower set point for when fuel is more expensive (i.e. peak rate). It is recommended that the lower set point is programmed to be your minimum temperature, if the pond then drops below this temperature during the day the heater can top up the heat to keep the pond at the minimum temperature.

Click Here For Installation & Operating Manual PDF
Customer Reviews (0)